Towards a new extrusion aluminum alloy system through integrated computational materials science and

来源 :15th International Conference on Aluminium Alloys(ICAA15)(第十 | 被引量 : 0次 | 上传用户：allench9484

【摘要】

：

【作者】

：

Kaan Inal Raja K.Mishra

【机构】

：

Department of Mechanical and Mechatronics Engineering, University of Waterloo, Canada

【出处】

：

15th International Conference on Aluminium Alloys(ICAA15)(第十

【发表日期】

：

2016年3期

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

Aluminum, with a density of 2.7 g/cm3, is the dominant light metal used in automotive applications today.In this research, a new technology platform is presented to design and manufacture a front rail from an aluminum alloy.The 6xxx alloy system is preferred for the front rail since it can be precipitation hardened as well as heat-treated, making it a perfect candidate for extrusion.

其他文献

Microstructure simulation of AA3105 aluminium alloy during homogenization treatment

In this study, the microstructural evolution of an as-cast AA3105 aluminium alloy during homogenization treatment was simulated with the ClaNG model.The simulated data were compared with experimental

会议

Thermodynamic assessment and determination of phase diagram including spinodal lines in Al-Mg alloy

Although several investigations on thermodynamic modelling in Al-Mg alloys were carried out, all previous thermodynamic descriptions have not been able to calculate the metastable phase diagrams of or

会议

Heat transfer coefficient of cold rolled strip during fast heat-treatment process in floater-type fu

T4 process of cold rolled strip in the floater-type furnace has high heat transfer efficiency.In order to study the rapid characteristic, heat transfer equation of strip in floater-type furnace is est

会议

Microsegregation modeling occurring during direct energy deposition of AlSi10Mg alloy

Powder deposition is the main direct energy deposition (DED) additive manufacturing technique.To date, the bulk of the work was carried out on Ti, SS and Superalloys.With respect to Al alloys, the lit

会议

Characterization and modelling of the damage behaviour of extruded aluminium profiles for crash simu

Aluminium profiles show very often an anisotropic deformation behaviour and inhomogeneous properties over cross section especially of thick-wall profiles.The damage behaviour of aluminium profiles dep

会议

The possibilities to lower the stacking fault energies of aluminum materials investigated by first-p

The stacking fault energies (SFEs) of various aluminum solid solutions were investigated against temperature and solute concentration using first-principles energy calculations.Three types of impuriti

会议

Modelling flow curves and creep in aluminium alloys

In through-process simulations of.aluminium sheet production, several physical models are needed to simulate all relevant hardening and softening mechanisms during rolling and annealing.By coupling th

会议

Numerical analysis of wavy interface formation and successive temperature change in magnetic pulse w

Magnetic pulse welding (MPW) which is one of the impact welding methods is suitable for a wide variety of combinations of similar and dissimilar metals.The flyer plate is accelerated by electromagneti

会议

Numerical analysis of deformation modes in aluminum rings under axial compression

Aluminum rings with various height/diameter/thickness ratios under axial compression are numerically studied.All the numerical simulations are based on an elastic-viscoplastic constitutive model.The e

会议

Material selection model for ultralight automobile using F-VIKOR

The development of ultralight automobile has motivated the lightweight material selection, which has been recognized as a MCDM (multi-criteria decision making) issue, a complex process for its multi-c

会议

Towards a new extrusion aluminum alloy system through integrated computational materials science and

与本文相关的学术论文