• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Effect of Cu and Mg/Si ratio on the intergranular corrosion resistance of 6000-series aluminum alloy

Effect of Cu and Mg/Si ratio on the intergranular corrosion resistance of 6000-series aluminum alloy

来源 :15th International Conference on Aluminium Alloys(ICAA15)(第十 | 被引量 : 0次 | 上传用户：ciancomjy
【摘 要】
：
6000-series aluminum alloys with high Cu or excess Si addition were susceptible to intergranular corrosion (IGC).The corrosion behavior of four alloys with different Cu content and Mg/Si was investiga
【作 者】
：
Yun Zou Tao Cheng Lipeng Ding Zhihong Jia Qing Liu 
【机 构】
：
Chongqing University, China
【出 处】
：
15th International Conference on Aluminium Alloys(ICAA15)(第十
【发表日期】
：
2016年3期
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
6000-series aluminum alloys with high Cu or excess Si addition were susceptible to intergranular corrosion (IGC).The corrosion behavior of four alloys with different Cu content and Mg/Si was investigated in this study.The four alloys were solution heat treated at 560℃ for 30 min, subsequently quenched in cold water and aged at 180℃ to the peak aging temper.
其他文献
Influences of extrusion parameters and artificial aging on the microstructure and the mechanical pro
Based on their high strength the almost Cu-free Al-alloy 7108 and the high Cu-containing alloy 7175 are interesting for the industry.However, the ductility of these alloys is low compared to other Al-
会议
Study on the microstructural evolution of a new type Al-Zn-Mg-Cu ahoy with Er and Zr additions durin
The presence of large constitutive particle formed during solidification decreases the strength and hot workability of aluminium alloys.Therefore, the evolution of these phases is a major issue in the
会议
The influence of heat treatment on phase composition, texture and mechanical properties of Al-Cu-Li
Phase composition, texture and mechanical properties of 80 mm plates from Al-2.8Cu-1.7Li-0.5Mg-0.5Zn-0.1Zr-0.06Sc alloy were investigated.It has been found that strength characteristics are maximum in
会议
The effect of the thermo-mechanical treatment of pre-aging, pre-stretching and re-ageing on microstr
A new thermo-mechanical treatment consisting of pre-aging, pre-stretching, and re-aging was used to improve mechanical properties of 7093 Al alloys casting by ourselves.Hardness testing, ensile testin
会议
An innovative methodology for optimisation of properties, costs and sustainability of aluminium allo
The present paper describes an innovative methodology for optimization of product properties, production costs and environmental impact in fabrication of aluminium alloys.The main idea is to represent
会议
Experimental and numerical investigations on back-end effects of hollow aluminium profile during por
Back-end effect is one of most common effects during hollow profile extrusion, which has great influence on the product rate and production costs.The purpose of the present study is to investigate exp
会议
A quantitative study on the influence of through thickness texture variation on the anisotropic mech
The anisotropic mechanical behavior of aluminum extrusions is of interest to industry in terms of formability and crash behaviour.Depending on the homogenization and extrusion conditions a wide range
会议
Persistence of shear-type textures during annealing of ECAE-processed ultrafine grained materials: A
Understanding the annealing behavior of ultrafine-grained materials produced by severe plastic deformation is of interest for applications requiring a balanced strength and ductility.In this study, co
会议
Numerical simulation of residual stress in Al-Cu alloy component during quenching and reduction of q
In this study, residual stress development during quenching and cold compressive stress relief processes of complex component were studied by numerical simulation and experimental methods.An iterative
会议
Tube hydroforming characteristic of Al alloy with different heat treatment conditions
Tube hydroforming is metal forming technology that utilized internal pressure and axial compressive loads to generate designed product shapes with complex section from tubular materials.The tube hydro
会议