Study on creep model of WPC prepared by formingmat-compression molding

来源 :第二届中国国际复合材料科技大会 (CCCM-2) | 被引量 : 0次 | 上传用户:wzmhua
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  Fiber of 40-80 mesh reinforced HDPE composite was prepared by forming mat-compression molding.The flexural properties, 24 hours creep-24 hours recovery of the resulted WPC was studied.And two-parameter power law model, Findleys power law model and Burgers model were used to describe the 24 hour creep curve of the resulted WPC.
其他文献
Petal-like MnO2/reduced graphene oxide (RGO) composites are fabricated via a simple hydrothermal process and used to construct supercapacitors as electrode materials with high loading mass of active m
Owing to its extremely high surface area as well as fantastic hydrophobic and mechanical, electrical properties, lipophilic graphene nanosheets have attracted much attention in many potential applicat
In this work, the long glass fiber reinforced PP (LCFGF/PP) composites were prepared by a convenient process of melt impregnation assisted by a double screw extruder to improve continuous long fiber c
采用粘稠塑性加工方法制备了方形锆钛酸铅压电纤维复合材料,研究了环氧树脂中不同TiO2含量对压电纤维复合材料的电学阻抗、介电性能、抗拉以及驱动应变性能的影响。结果 表明:环氧树脂中TiO2含量不同,压电纤维复合材料的谐振频率略有差别。随着环氧树脂中TiO2含量增多,压电纤维复合材料的电容值增大,但其抗拉强度及纵向自由应变值均表现出先增加后减小的规律。
本文采用阻抗匹配技术,利用金属栅网电调谐单元,对大型分块介质天线罩的板块接缝(或称加强肋)进行了电调谐优化设计,优化设计的含有金属栅网的混合介质结构,在保证接缝结构力学性能的前提下,其透波性能比板块接缝本身的透波率提升约20%,而且通过加载不同的金属栅网,可以调整混合结构最佳透波的频率范围,从而可用于不同频段天线罩的研制,为研制高性能大型介质天线罩提供了一条新的技术途径。
In this paper, impedance matching and electrical characteristics of hybrid dielectric rib in the large dielectric radome with metallic wire grids are studied in detail.With pre buried metallic wire gr
Natural chitosan (CS) at four different additions (10, 20, 30 and 40 phr) and particle size ranges (100-140, 140-180, 180-220, and over 260 mesh) are selected to improve the interface adhesion as well
This study mainly aimed at investigating the effects of volatile chemical components of wood species on mould and termite resistance of wood plastic composites (WPC) using artificial accelerated tests
In this paper, wood-rubber composites (WRCs) has been successfully manufactured through rubber mixing and vulcanization molding process using wood fiber and unvulcanized tire rubber compound.The effec
With the increasing pressure on the worlds resources as well as concerns about the disposal of materials, biodegradable materials have received lots of research attention.Poly(lactic acid) (PLA) with