【摘 要】
：
A vertical edger is a critical component of the roughing mill,used to reduce the width of steel slabs.When a vertical edgerexperiences a failure,it directly affects the production of the roughing mill
【机 构】
：
Center for Innovation through Visualization and Simulation(CIVS) Purdue University Calumet,2200 169t
【出 处】
：
第十届中国钢铁年会暨第六届宝钢学术年会
论文部分内容阅读
A vertical edger is a critical component of the roughing mill,used to reduce the width of steel slabs.When a vertical edgerexperiences a failure,it directly affects the production of the roughing mill.One such failure that has occurred took place in the R2 housing,which is not a typical location for failure to occur.The housing is designed to withstand significant force,but the maximum threshold for duration and intensity before failure occur are unknown.In addition to the force,many other factors affect theremaining life of a component,and life prediction is difficult predict.Furthermore,new steels seem to be pushing the roughing mills harder than before,and it is crucial to know how far they can be pushed before components break.The purpose of this research is to simulate the edging process using Finite Element Analysis(FEA)model.By performing a numerical analysis of the components in a vertical edger,an improved understanding of the mechanical behavior and potential failures can be identified to improve safety.
其他文献
This paper presents a new method for characterizing the interface stresses between an elastic rough ball and a smooth rigid plate under lubrication.Both micro asperity deformation and macro elastic de
总结了近年来宝钢股份高炉历史休风减矿基本情况及特点,提出简洁、高效的“一次方程式”休风减矿标准公式对原来休风减矿标准作了优化和改进,分析、对比了采用新的减矿标准前后在送风恢复时间、炉温水平等方面的成效,得出结论:宝钢在大高炉休风减矿方面积累了成功的技术和经验,休风减矿标准不断改进、完善,为高炉顺利休风、复风奠定了坚实的技术基础.高炉休风减矿的核心关键在于:根据休风时间、基础矿焦比、炉况状态、休风工
对重钢一炼钢厂1号板坯连铸机各类漏钢事故的分析,发现黏结漏钢是主要因素.进一步分析发现结晶器液面波动大、SEN潜入深度不合适、生产条件保障不到位及保护渣性能波动等容易造成黏结漏钢的发生,在对1号连铸机发生的漏钢事故进行分析基础上，一炼钢厂进行了防漏钢攻关，提高设备精细化管理水平、制定操作及工艺规范化措施，依靠漏钢预报自动报警以及人工监护，大大减小了漏钢几率。
研究了CSP流程生产的无取向电工钢50W800组织、织构及夹杂物特点,结果表明:(1)成品板为再结晶组织,晶粒尺寸为43.68μm;(2)成品织构以{111}面织构为主,{111}含量达到35.8％;(3)成品板夹杂物以氧化物和硫化物的复合夹杂为主.
利用金相显微镜、TEM等方法分析了不同保温温度和冷却速度对C-Si-Mn-Nb系高强冷轧板显微组织、力学性能和第二相粒子析出行为的影响.结果表明:50℃/s冷速下,保温温度低于800℃时出现带状马氏体,强度高,延伸率较低,超过840℃时铁素体体积分数显著下降,并出现M-A和残奥组织,在820℃时,马氏体组织弥散分布在铁素体基体上,观察到尺寸在7～9nm之间的Nb(C,N)析出物,其综合力学性能最佳
本文对俄罗斯高硅管线钢K52的成分、性能及组织进行了研究,并将其与API X56管线钢进行了对比研究.研究结果表明,K52在成分上采用高硅低锰的成分体系,在强度上与API X56管线钢相近.但K52对塑形和韧性要求更高,要求屈强比≤0.86,-20℃V型冲击功和-60℃的U型冲击功.对于俄罗斯高硅管线钢K52,由于其高硅低锰的成分体系,热轧过程中其氧化铁皮较为严重,较低的出炉温度可以减少氧化铁皮厚
Martensitic advanced high strength steel(MS-AHSS)belongs to a new class of steels that are currently used in the manufacture of lightweight yet crashworthy cars.One issue with using high-strength stee
The hydrogen permeation behaviour of DP and Q&P grades of advanced high strength steels was investigated using the permeability experiments(1)under cathodic charging at different potentials in 0.1 M N
通过对316L不锈钢丝试样的微观组织和表面缺陷进行观察、对表面应力状态进行分析、对试样力学性能进行测试,探究冲压后产品的表面缺陷成因.结果表明:不合格试样的表面缺陷主要有牙齿印、凹坑和擦伤;进口原料试样的抗拉强度为671.4MPa,屈服强度为272.9MPa,延伸率为56.9％,而国产原料试样的抗拉强度为672.9MPa,屈服强度达到287.7MPa,延伸率仅为47.9％;国产钢丝冲压后组织更粗大
The grain refinement of static castings and DC-casting ingots was achieved with a low-voltage pulsed magnetic field setup.Through the study of the interaction between melt and the low-voltage pulsed m