Synthesis of carbon dots doped in sodium borosilicate monolithic gel with tunable photoluminescence

来源 :2014中国溶胶-凝胶学术研讨会暨国际论坛 | 被引量 : 0次 | 上传用户:sevenqjq
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  We demonstrate carbon dots with tunable photoluminescence embeded in sodium borosilicate monolithic gel by sol-gel method and produce white light when directly combined with commercially available blue light emitting diodes.The carbon dots with tunable photoluminescence for these experiments were synthesized by one-pot pyrolysis method.The characterization of the resulting carbon dots monolithic gel was accomplished by using FTIR, transmission electron microscopy,energy dispersive X-ray spectrum.The fluorescence spectroscopies measurement showed carbon dots have highly fluorescence, and carbon dots monolithic gel also shows highly fluorescence with excitation-dependent emission.Meanwhile, The emission color is tunable by variations of carbon dots concentration in sodium borosilicate monolithic gel.To present, the carbon dots monolithic for white-emitting LED is never reported before.And now we synthesised carbon dots monolithic gel has the maximum luminous efficacy exceeding 61 lm/W at the correlated color temperature of ~ 6670 K is obtained.The carbon dots monolithic gel demonstrate a strong fluorescence and make it promising potential in white-emitting LED.
其他文献
To modify the oxidative-resistantability of carbon fiber reinforced carbon aerogelthermal insulators, Si-C-Oprecursor sol was prepared with dimethyldiethoxylsilane (DMDES) and methyltrimethoxysilane (
采用过氧钼酸溶胶-凝胶体系首先在SiC颗粒表面包覆MoO3涂层,然后氢气两步还原得到Mo涂层,研究了溶胶-凝胶工艺对MoO3包覆完整性的影响及还原后Mo涂层的成分和形貌;然后,选取Mo包覆SiC粉和Cu粉,采用热压烧结工艺制备了SiCp/Cu复合材料,重点对比分析了Mo界面阻挡层对复合材料导热性能的影响.结果表明:SiC表面丙酮和氢氟酸预清洗处理有利于MoO3涂层的沉积生长;当SiC/MoO3=5
以高锰酸钾为氧化剂,浓硫酸和浓硝酸混合配制的混酸作为反应环境,对PAM型碳纤维进行表面改性,然后以改性碳纤维作为经线和纬线织造成织物,经分切得到的一定宽度的基带,接着通过静电吸附上质量分数0.5-3%的碳粉,最终制成改性碳纤维色带.通过红外(FT-IR),x射线衍射(XRD),扫描电子显微镜(SEM)表征了改性前后的纤维特性变化;分别利用Printronix p7010和Printronix p7
本文在不添加还原剂情况下,以PVP为保护剂采用亚临界水热还原制备水溶性纳米银溶胶,并通过UV-Vis光谱实验探索了前驱体、PVP含量、水热反应时间等因素对制备纳米银溶胶的影响.结果表明:[Ag(NH3)2]OH络合离子水溶液是制备纳米银溶胶的高效前驱体;亚临界状态下可有效激发PVP分子中氮原子和氧原子上的孤对电子产生自由电子促使前驱体中Ag+的还原;PVP可有效阻止银粒子间的团聚,当水热反应时间为
Graphic and iron powders natural micro-alloyed with Ti and V elements were processed by mechanical milling process.The effects of C concentrations and milling processing parameters on powder particle
研究了以恒电流微弧氧化的方式在TC4钛合金表面制备多孔生物陶瓷层的较佳工艺和性能.利用响应曲面设计对恒电流微弧氧化各工艺参数进行设计,利用粗糙度仪、显微硬度仪、X射线衍射仪、扫描电镜等仪器分析检测了膜层的粗糙度、显微硬度、物相组成和表面形貌.讨论了在不同工艺参数下获得膜层的各种性能变化.研究结果表明:当Ca/P为1,正向电流为3A,时间为15min,频率为317.32Hz时,恒电流微弧氧化制备的多
Layered LiNi1/3Co1/3Mn1/3O2 was synthesized by co-precipitation method, and a series of LiNi1/3Co1/3Mn1/3O2/C composites were then prepared by Citric acid, on the surface of LiNi1/3Co1/3Mn1/3O2 using
The VOx nanosheets cathode materials for Li-ion battery have been synthesized from V2O5 powders and carbon aerogels via sol-gel and hydrothermal methods.The carbon aerogels are produced through superc
The WO3 nanostructure materials have been synthesized from tungsten powder and tungsten oxide sols as precursors via sol-gel method and hydrothermal process.The structure of WO3 nanoproduct is charact
Cu species (Cu Nps, Cu2+) and Sr2+ doped Na2O-B2O3-SiO2 (NBS) glass was prepared by sol-gel and atmosphere control methods.The formation mechanism and the microstructure of the specimens were investig