Research progress on microstructure evolution of semi-solid aluminum alloys in ultrasonic field and

来源 :中国铸造：英文版 | 被引量 : 0次 | 上传用户：bigsoul

【摘要】

：

The effects of ultrasonic vibration(UV)treatment on microstructure of semi-solid aluminum alloys and the application of UV in rheocasting process are reviewed.G

【作者】

：

Wu Shusen Lin Chong Lü Sh

【机构】

：

StateKeyLaboratoryofMaterialsProcessingandDie&,MouldTechnology

【出处】

：

中国铸造：英文版

【发表日期】

：

2014年4期

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

The effects of ultrasonic vibration(UV)treatment on microstructure of semi-solid aluminum alloys and the application of UV in rheocasting process are reviewed.Good semi-solid slurry can be produced by high-intensity UV process for aluminum alloys.The micr

其他文献

INDUSTBY NEWS

Recently, Chongqing Xianyou Technology Development Co.,Ltd. settled its new energy electric vehicle project and aluminumalloy die-casting project in Chongqing S

期刊

焦点新闻新能源重庆中国

Influence of wet activation of used inorganic binder on cyclically refreshed water glass moulding sa

The paper presents the research results of using an innovative method to reclaim the waste moulding sands containing water glass. Two of the examined processes

期刊

Microstructural evolution of direct chill cast AI-15.5Si-4Cu-1Mg-1Ni-0.5Cr alloy during solution tre

热处理在微观结构和为这些合金的大多数普通的使用的热处理方法是的 Al-Si alloys.The 的机械性质上有重要影响 age-hardening.This 纸跟随的答案处理调查在答案以后的演员

期刊

Al-Si合金答案处理微观结构金属间化合的化合物Al-Si alloy solution treatment microstructure inter

Rheological behavior of semi-solid TiB_2/7075 composites and simulation of their rheocasting process

In the present study, in-situ Ti B2 particle-reinforced 7075 aluminum alloy was produced by adding a mixture of K2 Ti F6 and KBF4 to the molten base alloy. The

期刊

Titles of papers published in FOUNDRY journal（Chinese edition）from Vol. 66, No.7 to 12, 2017

期刊

Press Conference of METAL AP 2018 was held in Bangkok, Thailand

期刊

新闻发布会金属AP曼谷泰国科学技术协会铸造材料工业组织

A comparative study of Mg-Gd-Y-Zr alloy cast by metal mould and sand mould

在金属模子和沙模子之间的微观结构和机械性质的差别扔了 Mg-10Gd-3Y-Zr 合金在当演员组状况下面并且在答案热处理以后被调查。在当演员组标本，微观结构 -Mg 固体答案和 -Mg+

期刊

金属模具砂模铸造合金铸造锆合金镁Y型钆机械性能Mg-10Gd-3Y-Zr alloy solution heat treatment peak

Evidence of refilled chamber gas pressure enhancing cooling rate during melt spinning of a Zr50Cu40A

The influence of the refilled gas pressure on the glass forming behaviour of one of the best ternary glass forming alloys Zr50Cu40AI10 was studied for the melt

期刊

metallicGLASSamorphousALLOYMELTSPINNINGGLASSformingbehaviourmetallic gl

Investigation of ductile iron casting process parameters using Taguchi approach and response surface

To find the optimized levels of various casting parameters in the ductile iron casting, various casting defects and the rejection rate were observed from a medi

期刊

Effect of nodule count and austempering heat treatment on segregation behavior of alloying elements

The equilibrium partition ratio, k, has been measured for Mn, Mo, Si, Ni and Cu in a ductile iron with composition(wt.%): 3.45 C, 0.25 Mn, 0.25 Mo, 2.45 Si, 0.5

期刊

Research progress on microstructure evolution of semi-solid aluminum alloys in ultrasonic field and

与本文相关的学术论文