Lipid droplets as endogenous intracellular microlenses

来源 :光:科学与应用(英文版) | 被引量 : 0次 | 上传用户:zhenzhurujun
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Using a single biological element as a photonic component with well-defined features has become a new intriguing paradigm in biophotonics. Here we show that endogenous lipid droplets in the mature adipose cells can behave as fully biocompatible microlenses to strengthen the ability of microscopic imaging as well as detecting intra-and extracellular signals. By the assistance of biolenses made of the lipid droplets, enhanced fluorescence imaging of cytoskeleton, lysosomes, and adenoviruses has been achieved. At the same time, we demonstrated that the required excitation power can be reduced by up to 73%. The lipidic microlenses are finely manipulated by optical tweezers in order to address targets and perform their real-time imaging inside the cells. An efficient detecting of fluorescence signal of cancer cells in extracellular fluid was accomplished due to the focusing effect of incident light by the lipid droplets. The lipid droplets acting as endogenous intracellular microlenses open the intriguing route for a multifunctional biocompatible optics tool for biosensing, endoscopic imaging, and single-cell diagnosis.
其他文献
内高压成形技术在现代汽车工业领域应用广泛.内高压成形与冲压焊接相比有如下优点:降低整车质量,实现轻量化;减少零件和模具数量,降低工装开发费用;可减少后续机械加工和组装焊接量;提高整车强度与刚度,尤其提高疲劳强度;提高材料利用率.rn内高压成形主要缺点:由于内压高,需要大吨位液压机提供合模压力;高压源及闭环实时控制系统复杂,造价高;由于成形缺陷和壁厚分布与加载路径密切相关,零件试制研发费用高,必须充分利用数值模拟进行工艺参数优化.
管材成形技术rn制管rn焊管加工流程包括:钢卷(或板)剪切、成形、焊接、探伤、校直、切断、包装等,如图1所示.成形工艺的不同,焊接工艺也不同.高频焊接适用于直缝焊管,尺寸精度好、价格低、生产效率高,优良的综合机械性能;激光焊管设备昂贵,用于大批量自动化生产,接头性能好.常见威形工艺及焊接工艺见表1.
Color vision is used throughout medicine to interpret the health and status of tissue. Ionizing radiation used in radiation therapy produces broadband white light inside tissue through the Cherenkov effect, and this light is attenuated by tissue features
期刊
随着人们对汽车减重、节能、降耗等问题的关注,汽车轻量化成为汽车制造企业重要研究课题.汽车排气用不锈钢管材的弯管和液压成形技术为实现汽车轻量化提供了技术保障.我公司能够针对汽车排气系统各种异形管件难加工问题,进行设计优化加工,制备相应生产模具,为汽车企业生产各类性能优异的零部件.
期刊
冲压件缩颈开裂问题,是冲压专业的行业难题,在一定程度上制约冲压生产.管控缩颈开裂是一个系统工程,笔者所在团队通过几年的攻关,在缩颈开裂控制上取得较大突破,并积累了一套行之有效的管控方法.rn缩颈开裂的系统管控,解决了由于成形裕度不足导致的一些可识别的缩颈开裂问题,但对于生产过程中由于模具异常损伤、设备压力异常变化、零件表面油膜异常变化等突发原因导致的偶发缩颈开裂问题,以及一些不易识别的由于成形间隙过小导致的缩颈开裂问题,缺乏有效的识别和监控手段.
期刊
Optical interference is not only a fundamental phenomenon that has enabled new theories of light to be derived but it has also been used in interferometry for the measurement of small displacements, refractive index changes, and surface irregularities. In
期刊
背门内板是典型的车身内覆盖件之一,该零件曲面形状复杂,一般为空间三维曲面,且外形尺寸大,具有许多凸台和凹槽,在冲压过程中容易出现开裂和起皱现象.某车型后备厢内板在生产中,经常出现滑移起皱和开裂交替发生情况,如图1所示.每批次都要调整气垫力、涂油等工艺参数.影响了生产效率,同时也产生了较多返修和报废,解决此问题非常迫切.
期刊
Ratiometric luminescence thermometry with trivalent lanthanide ions and their 4fn energy levels is an emerging technique for non-invasive remote temperature sensing with high spatial and temporal resolution. Conventional ratiometric luminescence thermomet
期刊
侧围外板是车身最重要的零件,同时也是模具开发过程中工艺开发难度非常大的零件.侧围外板潜在的工艺难点和质量缺陷比较多.随着冲压成形CAE分析技术的发展和应用,为在工艺审查和工艺设计阶段规避质量缺陷,确保模具开发周期提供了有效的保证手段.
管材液压成形(也称内高压成形)是使用液体对管材施加压力,使其在模具中成形的一种塑性加工技术.与传统工艺相比,管材液压成形可以做出很多刚性模具无法成形的复杂零件,此外,液压成形的零件具有轻量化、高强度等优点,可以减少料耗,工艺过程稳定,产品一致性好,在汽车排气、底盘、车身零部件中获得广泛应用.