河南省水利厅采取多种形式开展学习教育

来源 :河南水利与南水北调 | 被引量 : 0次 | 上传用户:ljl640211
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
为确保学习教育不走过场,河南省水利厅以领导带头为抓手,按照厅领导班子、厅机关各处室和厅属单位三个层次,采取党组中心组学习、集体学习、专家辅导、专题活动四项措施,狠抓党的群众路线学习教育。一是坚持中心组学习。按照每周一次的学习计划,厅党组中心组通过专题报告会、班子成员交流体会等形式,切实做到领导带头学习,带头作报告、带头写体会,先学一步、学深一步。王小平厅长在厅党组中心组学习扩大会上带头做了“以红旗渠精神为指引,扎实推进群众路线教育实践活动”的专题辅导报告。其他党组成员,每次两名厅级干部做一次专题学习汇报。 In order to ensure that learning and education do not go through the field, Henan Provincial Department of Water Resources to take the lead as the starting point, according to the hall leadership team, the Office of the Office of organs and offices of the three levels, take the party group center group learning, collective learning, expert counseling, special activities Four measures, pay close attention to the party’s mass line learning and education. First, adhere to the central group learning. In accordance with the weekly study plan, the hall party group and center group through the special report, the exchange of experience and other members of the team to effectively implement the leadership take the lead in learning, take the lead for the report, take the lead in writing experience, learn first, learn a step further. Director Wang Xiaoping took the lead in “Expanding Party Learning Group Meeting at the Central Party Group Meeting of the Party Hall” and “Guided by the spirit of the Hongqi Canal, and steadfastly promoted the practice of mass line education”. Other party members, each time two department-level cadres to do a special study report.
其他文献
期刊
在党的群众路线教育实践活动中,省移民办结合移民征迁工作实际,以“三查三帮”为重点,在全省移民征迁系统深入开展“下基层、解民忧、办实事”活动,动员组织各级党员干部深入
介绍铝材等温/等压挤压工艺的发展概况,重点论述了铝材热坯料梯度水冷工艺的特点,对比分析了该工艺在不同条件的应用效果.结果认为,该方法能提供多种精确的温度梯度,是正挤压
从生产6061-T6511铝合金大规格挤压板材晶粒粗大、力学性能不达标入手,分析了其缺陷产生及力学性能不合格的原因,提出了相应的解决措施,满足了生产的需要.
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生、测量监控等方面人手,介绍了S226海滨大桥
期刊
期刊
1.区域概况张家口水文站是清水河代表站,清水河是永定河上游洋河的一条较大支流,流域内主要有东沟、正沟、西沟3条支流,流域地势北高南低,河道纵坡9.54‰。东沟植被最好,两侧
利用亚硫酸钙型脱硫灰处理铝材生产中的铬化废水,以废治废,可同时脱除废水中的六价铬和氟离子,六价铬浓度可降至0.06 mg/L以下,氟离子浓度降至10 mg/L.相关工艺控制条件为:铬