Algorithm and experiments of six-dimensional force/torque dynamic measurements based on a Stewart pl

来源 :Chinese Journal of Aeronautics | 被引量 : 0次 | 上传用户:z88981414
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Stewart platform(SP) is a promising choice for large component alignment, and interactive force measurements are a novel and significant approach for high-precision assemblies. The designed position and orientation(P&O) adjusting platform, based on an SP for force/torquedriven(F/T-driven) alignment, can dynamically measure interactive forces. This paper presents an analytical algorithm of measuring six-dimensional F/T based on the screw theory for accurate determination of external forces during alignment. Dynamic gravity deviations were taken into consideration and a compensation model was developed. The P&O number was optimized as well.Given the specific appearance of repeated six-dimensional F/T measurements, an approximate cone shape was used for spatial precision analysis. The magnitudes and directions of measured F/Ts can be evaluated by a set of standards, in terms of accuracy and repeatability. Experiments were also performed using a known applied load, and the proposed analytical algorithm was able to accurately predict the F/T. A comparison between precision analysis experiments with or without assembly fixtures was performed. Experimental results show that the measurement accuracy varies under different P&O sets and higher loads lead to poorer accuracy of dynamic gravity compensation. In addition, the preferable operation range has been discussed for high-precision assemblies with smaller deviations. Stewart platform (SP) is a promising choice for large component alignment, and interactive force measurements are a novel and significant approach for high-precision assemblies. The designed position and orientation (P & O) adjusting platform, based on an SP for force / torquedriven This paper presents an analytical algorithm of measuring six-dimensional F / T based on the screw theory for accurate determination of external forces during alignment. Dynamic gravity deviations were taken into consideration and a compensation model was developed. The P & O number was optimized as well. Given the specific appearance of repeated six-dimensional F / T measurements, an approximate cone shape was used for spatial precision analysis. The magnitudes and directions of measured F / Ts can be evaluated by a set of standards, in terms of accuracy and repeatability. Experiments were also performed using a known applied load, and the proposed analysis A comparison between precision analysis experiments with or without assembly fixtures was performed. Experimental results show that the measurement accuracy varies under different P & O sets and higher loads lead to poorer accuracy of dynamic gravity compensation. In addition, the preferred operation range has been discussed for high-precision assemblies with smaller deviations.
其他文献
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生、测量监控等方面人手,介绍了S226海滨大桥
The drag-free satellites are widely used in the field of fundamental science as they enable the high-precision measurement in pure gravity fields. This paper in
L-band digital aeronautical communication system 1(L-DACS1) is a promising candidate data-link for future air-ground communication, but it is severely interfere
Inertial navigation system/visual navigation system(INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since v
Dramatic tool temperature variation in end milling can cause excessive tool wear and shorten its life, especially in machining of difficult-to-machine materials
Inspection techniques for aero-engine blades are a hot topic in industry. Since these blades have a sculptured surface and a small datum, measurement results ma
Since digital circuits have been widely and thoroughly applied in various fields, electronic systems are increasingly more complicated and require greater relia
Plastic wrinkling predictions and shear enforced wrinkling characteristics of Ti-alloy thin-walled tubes under combination die constraints have become key probl
Air traffic flow management(ATFM) is a collaborative process between the airspace provider and the airspace users. The result of the collaboration should be an
This paper focuses on the type synthesis of two degree-of-freedom(2-DoF) rotational parallel mechanisms(RPMs) that would be applied as mechanisms actuating the