Fabrication and Testing of Metal Foil Planar Switch

来源 :Defence Technology | 被引量 : 0次 | 上传用户:qazmlp159753
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
A metal foil spark gap switch is fabricated by using magnetron sputtering deposition technology and standard microelectronic technology. The switch has two main electrodes and a trigger electrode. Stylus profiler is employed to measure the distance between the main electrodes and the dimensions of the trigger electrode. The discharge characteristics of the metal foil spark gap switch are discussed. The switch has short delay time and low time jitter. When it is fired by a conventional capacitive discharge unit (CDU), the firing circuit has low inductance and resistance. Because of its low profile structure, it can be easily integrated with the bridge foil used in a conventional exploding foil initiator system (EFIS). A metal foil spark gap switch is fabricated by using magnetron sputtering deposition technology and standard microelectronic technology. The switch has two main electrodes and a trigger electrode. The discharge characteristics of the metal foil spark gap switch are discussed. The switch has short delay time and low time jitter. Because of is fired by a conventional capacitive discharge unit (CDU), the firing circuit has low inductance and resistance. low profile structure, it can be easily integrated with the bridge foil used in a conventional exploding foil initiator system (EFIS).
其他文献
利用化学浴法制备了由六棱锥纳米分枝组成的多级分层花型结构的ZnO,并采用溶剂热法在所得ZnO材料表面均匀修饰Au纳米粒子。系统地研究了不同Au纳米粒子修饰量对ZnO气敏性能的
为了研究Sn对Mg-Al-Ca系合金热裂敏感性的影响,通过Clyne-Davies模型对MgAl_7Ca_1Sn_x(x=0,0.5,1,2)系合金的热裂敏感性进行预测。采用“T”型热裂模具,对MgAl_7Ca_1Sn_x系合
采用外观检查、扫描电镜(SEM)断口观察、金相(OM)检验等方法分析了TB8钛合金紧固件疲劳断裂后的断口形貌和显微组织,并对紧固件头部附近的受力情况进行了有限元模拟分析。研
在含有不同氟离子浓度的硅酸钠电解液体系中,采用恒压微弧氧化技术对AZ31镁合金进行表面处理,通过XRD、SEM、EDS等研究镁合金表面微弧氧化膜层形貌和相结构特征,探讨氟离子对
α相的析出形态和析出动力学对β钛合金的研究至关重要。本文利用光学显微镜(OM)、扫描电镜(SEM)、透射电镜(TEM)、硬度测量及拉伸性能测试等分析手段,研究了一种自主设计的
为明确内蒙古中部地区不同结构日光温室和增施CO_2对温室光温性能以及黄瓜生长发育的影响,以普通日光温室(A)及内保温日光温室(B)为试验温室,并设置4个试验处理:AE(普通日光
1一般资料患者,39岁,因"痛经进行性加重伴经量增多10余年"就诊,病程中曾在多家医院就诊,临床诊断为子宫腺肌病。来我院B超提示子宫均匀性增大,肌层回声不均匀,呈细密点状回声,
为了提高反应等离子喷涂纳米TiN涂层的致密性、消除涂层内的微观缺陷,在大气、氩气氛和真空中对其进行了热处理。用XRD、SEM、TEM分析了纳米TiN涂层热处理后相组成及组织结构
采用Φ7.62 mm装甲钢平头子弹对Ti-6Al-4V合金进行侵彻,分析了Ti-6Al-4V合金弹着点及其弹着点周围宏观与微观组织变化与损伤.结果表明,Ti-6Al-4V合金弹着点微观组织变化与损
采用霍普金森压杆(SHPB)对AZ31镁合金进行了高速切削实验。实验采用两把YT15硬质合金刀具,并对称地固定在实验装置上。在实验过程中,实验样品固定在样品台上,用霍普金森压杆