MATHEMATICAL ESTIMATION OF PHYSIOLOGICAL DISTURBANCES IN HUMAN DERMAL PARTS AT EXTREME CONDITIONS:ON

来源 :Analysis in Theory and Applications | 被引量 : 0次 | 上传用户:heiyun28
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
A mathematical model for the thermoregulation in the dermal layers of the human body is proposed.The skin is composed mainly of three layers-epidermis,dermis and subcutaneous tissues.The relative constancy of the body temperature is remarkable because there is a continuous exchange of heat with the external environment as well as within the different compartments of the body.A model describes the distribution of dermal temperature as a function of internal and external parameters,such as temperature of the incoming arterial blood,blood flow,ambient temperature,and heat exchange with the environment.It is shown that substantial changes in human dermal temperature can be accomplished only through changes in the temperature of the incoming arterial blood or substantial suppression of blood flow.Other parameters can lead only to temperature changes near the skin surface. A mathematical model for the thermoregulation in the dermal layers of the human body is proposed. The skin is composed mainly of three layers-epidermis, dermis and subcutaneous tissues. The relative constancy of the body temperature is remarkable because there is a continuous exchange of heat with the external environment as well as within the different compartments of the body. A model describing the distribution of dermal temperature as a function of internal and external parameters, such as temperature of the incoming arterial blood, blood flow, ambient temperature, and heat exchange with the environment. It is shown that substantial changes in human dermal temperature can be accomplished only through changes in the temperature of the incoming arterial blood or substantial suppression of blood flow. Other parameters can lead only to temperature changes near the skin surface.
其他文献
…0·oo…o·0,…o·。2 10·03)0·0‘10·05 10·o“10·0了…0·08 10·。q二黔胳摆糯摇淞宗宁薪 0 .3,、…0.:,9!0.;、 0 .83…0·88 10·‘·:,书令各誉留 ,·,31‘·,8
本文采用5种船体结构钢的约400个动态撕裂(DT)试验数据,讨论了各钢种DT试样上平台断裂吸收能(E_0),塑脆转变温度(_DT_rE)分别随板厚(B)的变化规律,并分别给出相应的经验公式
国内各厂生产的400毫米台扇,底板形状、尺寸与图1基本一致。它是一个倾斛3°30′的斜凸缘盒形件,5°为侧壁斜角。显然工件四圓角侧壁是母线为曲线的复杂空间曲面。 图1所示
据苏联1983年出版的《轻泡废钢加工用设备》一书介绍,近几年来,苏联开始注重发展三向挤压的废钢打包机。这种新式打包机与普通的二向挤压的废钢打包机相比,因多了一个主压,
在机器和机床制造业中球铁(?)得到广泛的应用。但是,对于在交变载荷条件下工作的零件,它的应用因疲劳极限低而受到限制。经试验表明,球铁用感应加热进行热处理,可以显著提高
研制出一种可对带材平直度和形状施加影响的系统,它易于同现有的设备结合,投资费用极小,不增加生产费用。结论CVC(可连续变动轧辊凸度)轧制工艺可通过 S 形弯曲的轧辊的应用
高一下学期开学,座位重新调整及分组的过程中,绝大多数学生都很兴奋,个别人看起来不是很情愿,但没有人提出异议。分完小组后各小组选举产生了小组长,在班长的主持下,召开了小组长会议。  开会的过程中,我注意到了一个小组长雨,始终闷闷不乐,一直没有参与发言。会后我将他单独留下来,问他情绪不佳的原因,他犹豫了半天才吞吞吐吐地说:“我不想和东分开坐。”说着眼泪就刷刷地淌下来。雨来自昆明郊县上的农村中学,性格较
轴承橡胶密封圈在我国的工业生产中,需求量日益增多,占有十分重要的地位。单件生产很不经济。我们设计的如图1所示压模,是在25吨面积为300×400毫米~2的橡胶压模机上使用的
一、前言排气管衬套系1Cr18Ni9 Ti钢经焊接而成。现行工艺规定用焊丝一次焊成,但库中尚有5000余件是采用金属本体自熔焊的,而自熔焊有部分焊缝没有焊透,使用过程中曾发现裂
我厂生产的隔离式自救器产品冲压件占产品零件总数的55%左右,模具比重大。模具质量的好坏,寿命的长短,将直接影响到产品质量和生产任务的按时完成。模具本身需要一种具有高