Influence of reaction gas flows on the properties of SiGe:H thin film prepared by plasma assisted re

来源 :Chinese Physics B | 被引量 : 0次 | 上传用户:Y13622229444
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
A new preparing technology,very high frequency plasma assisted reactive thermal chemical vapour deposition (VHFPA-RTCVD),is introduced to prepare SiGe:H thin films on substrate kept at a lower temperature.In the previous work,reactive thermal chemical vapour deposition (RTCVD) technology was successfully used to prepare SiGe:H thin films,but the temperature of the substrate needed to exceed 400 C.In this work,very high frequency plasma method is used to assist RTCVD technology in reducing the temperature of substrate by largely enhancing the temperature of reacting gases on the surface of the substrate.The growth rate,structural properties,surface morphology,photoconductivity and dark-conductivity of SiGe:H thin films prepared by this new technology are investigated for films with different germanium concentrations,and the experimental results are discussed. A new preparing technology, very high frequency plasma assisted reactive thermal chemical vapor deposition (VHFPA-RTCVD), is introduced to prepare SiGe: H thin films on substrate kept at a lower temperature. In the previous work, reactive thermal chemical vapor deposition (RTCVD ) technology was successfully used to prepare SiGe: H thin films, but the temperature of the substrate needed to exceed 400 C. In this work, very high frequency plasma method is used to assist RTCVD technology in reducing the temperature of substrate by substantially enhancing the temperature of reacting gases on the surface of the substrate. growth rate, structural properties, surface morphology, photoconductivity and dark-conductivity of SiGe: H thin films prepared by this new technology are investigated for films with different germanium concentrations, and the experimental results are discussed.
其他文献
本文详细讨论了由于设计基准与测量基准或工艺基准与测量基准不重合通过工序尺寸或测量尺寸换算,对零件设计尺寸进行间接控制或检验,由于尺寸链组成环误差之间的补偿,可能使
在无心磨床上磨削螺钉的螺纹部份滚丝前外圆时,如螺钉角买已铣好,或外露部份太长时,就给操作带来麻烦,这时可用如图所示方法来解决。在操作时通常使托板与导轮间的距离不变,
2009-2010赛季的意甲风雨飘摇,去年夏季球星转会风暴洗劫了亚平宁半岛后,联赛内部又起波澜:北方三强的地位已经受到了其他球队的巨大冲击,赛季初热那亚双雄接连称霸积分榜,如
鉴于钨系合金白口铸铁组织的复杂性和多样性,本文对各种成分的试样进行了金相、扫描电镜观察,并通过X光衍射、电子探针、显微硬度以及染色腐蚀等分析方法,对钨系铸铁的相组
许多零件的加工,按工艺要求是先划线再进行加工。平面划线容易掌握,而零件的立体划线较难掌握。例如,划小叉件时,要一次划出叉件三个方向的位置尺寸。一般是把零件装夹在方
后进生的转变,是高校学校管理和教学工作中的一个重要环节。体育教学中让学生在运动中领略豪迈、奔放的节律,在静止中感受刚毅、稳健,对于激发学生特别是后进生的自尊、自强
工艺文件的制订是生产技术准备工作的一部分,它对确保产品质量、组织和管理生产、估算产品的成本等都具有指导性的作用。然而,同样一个零件在同样的工艺条件下,工艺过程的制
小型刨床一般无自动抬刀装置,为了消除由此而带来的容易撞掉刀尖,后刀面易磨损的后果。在刨刀上安装了如图所示的自动抬刀装置。其结构简单、制作容易、使用方便。自动抬刀
在机床大修及维修过程中,特别是对于精密机床的修理,机床的滑动导轨,往往会产生重爬现象。这不仅使手轮驱动力和机床电功率增加,更严重的是破坏了导轨副的低速运动特性,影响
组合夹具整体布局将直接关系着夹具的刚性和精度,也影响着工件的加工精度和尺寸精度。所以,组装的整体布局要经多因素综合性分析和检验,比如不同类型、定位夹紧、夹具与机床