【摘 要】
：
The Nd(Ⅲ) extraction in flat renewal supported liquid membrane (FRSLM),with polyvinylidene fluoride membrane and renewal solution including HNO3 solution as th
【机 构】
：
Key Laboratory of Water Cycle and Related Land Surface Processes,Faculty of Water Resources and Hydr
论文部分内容阅读
The Nd(Ⅲ) extraction in flat renewal supported liquid membrane (FRSLM),with polyvinylidene fluoride membrane and renewal solution including HNO3 solution as the stripping solution and di(2-ethylhexyl) phosphoric acid (D2EHPA) dissolved in kerosene as the membrane solution,was investigated.The effects of pH in the feed phase,volume ratio of membrane solution to stripping solution,concentration of HNO3 solution and concentration of carrier in the renewal phase on extraction of Nd(Ⅲ) were also studied,respectively.As a result,the optimum extraction conditions of Nd(Ⅲ) were obtained when concentration of HNO3 solution was 4.00 mol/L,concentration of D2EHPA was 0.100 mol/L,and volume ratio of membrane solution to stripping solution was 1.00 in the renewal phase,and pH was 4.60 in the feed phase.When initial concentration of Nd(Ⅲ) was 2.00× 10-4 mol/L,the extraction percentage of Nd(Ⅲ) was up to 92.9％ in 75 min.
其他文献
采用10-6 s-1慢应变拉伸测试手段研究冷轧与拉伸复合预变形对2519A铝合金抗应力腐蚀开裂性能的影响.冷轧7％后再垂直拉伸3％的合金板材抗拉强度和应力腐蚀指数分别为481MPa和0.04
Eu-doped transparent oxyfluoride borosilicate glass ceramics containing Ba2GdF7 nanocrystals were prepared by controlling crystallization of melt-quenched glass
随着我国经济规模的迅速扩大和城市化的进程的加快,一些无序的过度开发和城市人口的快速增长,导致城市悬浮物和污染物排放大量增加,空气质量下降,城市的雾霾天气越来越多.文
薄壁铝合金管小弯曲半径数控弯曲是个多因素耦合、多模具约束下的复杂过程.提出以有限元模拟为基础,基于显著性的工艺参数优化方法,即采用析因因子设计分析工艺参数对成形质
采用一套新颖的反重力渗流装置制备开孔泡沫铝.研究表明,采用反重力渗流法所制备的泡沫铝,表现出优良的力学性能且几乎没有渗流不足与渗流过度的缺陷；泡沫铝中的空隙度对其力
Hydrodynamic performance of an ultra deep turret-moored Floating Liquefied Natural Gas (FLNG) system is investigated.Hydrodynamic modeling of a turret-moored FL
用磷酸三丁酯(TBP)溶剂浸渍高分子交换树脂XAD-16来制备浸渍树脂.在室温下,将未稀释的磷酸三丁酯与树脂按液固比6(磷酸三丁酯体积与树脂质量比)浸渍24 h得到的浸渍树脂的质量
通过热压缩实验研究热等静压态FGH96 合金的热变形行为和微观组织演化过程.基于Gleeble- 1500,在1000～1150℃和0.001～1.0 s-1的条件下进行热压缩实验.对应力一应变数据进行拟合
采用Al含量为2％～22％(质量分数)的ZnAl钎料,配合改进型CsF-AlF3钎剂,研究ZnAl钎料在3003铝合金板材上的铺展性能及钎焊接头的力学性能与显微组织.结果表明,当Al含量低于8％时,3003
通过SEM和DSC研究添加锂对A356合金的共晶变质效果的影响.SEM显微组织观察表明:当锂的添加量为0.3％(质量分数)时,A356合金的共晶组织形貌由条片状转变为纤维状的变质效果很明