【摘 要】
：
Aiming at the requirements of structural steel in Gen-IV nuclear reactor,the high-chromium martensitic heat-resistant steels containing 10-12％ chromium were developed.The toughness of heat-affected zones (HAZs) is one of the important factors for evaluati
【机 构】
：
College of Mechanical Engineering, Shenyang University,No.21, Wanghua Street, Dadong District, Sheny
论文部分内容阅读
Aiming at the requirements of structural steel in Gen-IV nuclear reactor,the high-chromium martensitic heat-resistant steels containing 10-12％ chromium were developed.The toughness of heat-affected zones (HAZs) is one of the important factors for evaluating the weldability of steels.In this paper,the simulated HAZs were fabricated using tempered SIMP steels.The effects of microstructures on the impact toughness of materials were analyzed using Vickers hardness tester,optical microscope,transmission electron microscope.Experimental results demonstrated that the HAZs of weldment were poor in toughness,much lower than that of the base metal.However,after experiencing post-weld heat treatment,the toughness of the HAZs increased greatly.The toughness became better in terms of CG-HAZ,FG-HAZ and IC-HAZ for the two steels,regardless of as-welded or after PWHT.Compared with SIMP7 steel,chemical compositions,such as C,Si,Mn and Cr,were adjusted to a lower content;the toughness of base metal and simulated HAZs was better in the case of SIMP11.The conjunct roles of dislocation density and carbon contents retained in the martensite led to poor impact toughness of the aswelded HAZs,because dislocations and carbon atoms affected the inner stresses within lattices.
其他文献
The rupture behavior of the modified 10Cr-lMo steel multi-layer welded joint is determined by the fine-grain zones of the weld metal adjacent to the fusion line during the long-term creep test at 620 ℃.The microstructures of multi-layer weld metal before
The tensile creep behavior of extruded Mg-6Gd alloy,having the tensile yield strength of ～ 110 MPa at 175 ℃,has been investigated under 175 ℃ and 150 MPa.In this study,the extruded Mg-6Gd sample exhibits the total tensile strain of ～ 10.5％ after the creep
The influences of heat treatment and test condition on the microstructure and stress rupture properties of a Ni-Mo-Cr-Fe base corrosion-resistant superalloy have been investigated in this paper.Optical microscope and scanning electron microscope were empl
Enhancing combinatorial properties,such as excellent corrosion resistance,high strength and good ductility combined,is an important issue for manufacturing high-quality AlMgSi(Cu) alloys.Here,we show that this can be achieved by optimizing a combinatorial
The application and component designs of single crystal superalloys are restricted by the precipitation of topologically closed packed (TCP) phases,which can deteriorate the microstructural stability of the alloys severely.Limited researches concerning th
In as-welded state,each region of 2219 aluminum alloy TIG-welded joint shows different microstructure and microhardness due to the different welding heat cycles and the resulting evolution of second phases.After the post-weld heat treatment,both the amoun
The cooling curves and the change of contraction/expansion during solidification and cooling were tested by using a selfmade device which could achieve the one-dimensional contraction instead of three-dimensional contraction of the casting.Then,the effect
The microstructure and mechanical properties of the as-cast and heat-treated Mg-4.6Y-2.5Zn-0.6Zr-xSn (x =0,0.2 and 0.5 wt％) alloys were investigated in this work.The results showed that the eutectics have been refined with 0.2％ Sn addition and it has no e
Previous studies showed that significant increases in elongation in Mg-Ce alloys due to the Ce addition and the solute drag effect by Ce addition were ascribed to the non-basal dislocation slip activating and the texture altering.The microstructure evolut
The Mg MB26/Al 7075 composite rod,in which Mg MB26 serves as the sleeve and Al 7075 serves as the core,is fabricated via the process of co-extrusion.The influence of extrusion speed on the microstructure evolution,interface bonding and mechanical response