【摘 要】
：
Interface engineering is an effective way to improve efficiency and long-term stability of perovskite solar cells (PSCs).Herein,an ionic compound tetrabutylammonium hexafluorophosphate (TP6) is adopted to passivate surface defects of the perovskite film.I
【机 构】
：
Key Laboratory of Applied Surface and Colloid Chemistry,Ministry of Education,Shaanxi Key Laboratory
论文部分内容阅读
Interface engineering is an effective way to improve efficiency and long-term stability of perovskite solar cells (PSCs).Herein,an ionic compound tetrabutylammonium hexafluorophosphate (TP6) is adopted to passivate surface defects of the perovskite film.It is found that TP6 effectively reduced the surface defects,especially at the grain boundaries where the defects are abundant.Meanwhile,the exposed long alkyl chains and fluorine atoms in the TP6 enhanced the moisture stability of the perovskite film due to its strong hydrophobicity.In addition,the driving force of charge carrier separation and transport is increased by enlarged built-in potential.Consequently,the power conversion efficiency (PCE) of PSCs is significantly improved from 20.59％ to 22.41％ by increased open-circuit vcltage (Voc) and fill factor(FF).The unencapsulated device with TP6 treatment exhibits better stability than the control device,and the PCE retains ～ 80％ of its initial PCE after 30 days under 15％-25％ relative humidity in storage,while the PCE of the control device declines by more than 50％.
其他文献
制备了水性环氧富锌底漆、水性环氧云铁中间漆和水性丙烯酸聚氨酯面漆为配套的水性重防腐涂料配套体系,并研究了配套体系的各项性能指标.结果表明,水性重防腐涂料配套涂层可以替代传统溶剂型涂料在腐蚀等级为C4(H)以下的腐蚀环境使用.
通过研究多官能度单体的用量,并使用乙基丁基丙二醇(BEPD)与饱和六元环结构1,4-环己烷二甲醇(CHDM)进行聚酯合成,结果表明,CHDM用量为4.5％,BEPD用量为7.1％,三羟甲基丙烷(TMP)用量为0.6％时,制备的96.5/3.5型羟烷基酰胺粉末涂层具有较好的机械性能、耐丁酮擦拭、贮存稳定性和优异的耐水煮性能;扫描电子显微镜结果表明,自合成聚酯制备的粉末涂层具有优异的流平性能.
传统的卷材涂料主要采用高温热固化工艺,由于固化速度慢、能耗高等缺点,难以满足高效涂装和环保的要求.紫外光固化(UV光固化)是一种环保型的加工技术,与传统热固化相比,UV光固化其有低能耗、低污染、固化速度快、产品性能好等诸多优点,尤其适合自动化生产线的高速涂装.本文将介绍卷材涂料及其涂装的技术特点和工艺要求、UV光固化技术在金属预涂卷材的发展情况和研究进展,并对紫外光固化涂料的特点、主要成分等方面进行了综述,并提出了该技术存在的主要问题和发展方向.
海底管道(以下简称海管)一旦发生泄漏事故,不但会造成石油开采平台生产停滞、产生巨大的经济损失,而且会造成严重的海洋生态污染,带来严重的社会影响.对海管的内腐蚀情况进行监测,及时发现潜在的失效风险,具有重要意义.本文总结了内腐蚀监测技术的分类、原理、特点和研究现状,指出了海管内腐蚀监测技术未来发展方向是无损检测技术与腐蚀在线监测技术融合应用、高海洋环境适用性和数字化远程管理.
电泳涂装时,车身内外表面钣金需要无油、无锈、无明显杂质,否则会直接影响电泳漆膜质量.为保证车身表面有良好的外观质量,涂装前处理和电泳过程中,均会采用大量的水对车身进行冲洗,因此涂装前处理、电泳成为汽车制造过程中用水最多的工序.本文主要针对降低自动葫芦输送设备涂装生产用水量的方法及控制进行研究,减少了涂装废水的排放.
The quantitative understanding of how atomic-level catalyst structural changes affect the reactivity of the electrochemical CO2 reduction reaction is challenging.Due to the complexity of catalytic systems,conventional in situ X-ray spectroscopy plays a li
通过对不同聚氨酯树脂、固化剂以及助剂进行性能评估,并考虑成本因素选择合适的原材料制备出具有优异疏水疏油性能的粉末涂料.同时,考虑油烟机工作环境,特别对涂层耐水性能进行了改进.对所制备的涂层进行性能检测,结果表明,涂层不仅具备防油污功能,易清洁,而且机械性能、耐水性能、外观装饰性优异.
Water oxidation is the key half reaction to achieve full splitting of water to hydrogen and oxygen.Herein,a binuclear complex,[(L4-)Co2Ⅲ(OH)]ClO4,was reported as a stable and efficient homogenous catalyst for electrocatalytic water oxidation in 0.1 M phos
电泳流痕问题是车身涂装过程中的一大难题,严重的电泳流痕不仅会影响外观而且还会制约车间正常生产,造成人力、物力浪费.电泳流痕的影响因素有很多,本文针对新车型电泳流痕问题,从焊装涂胶、车身匹配调整、设计更改、电泳工艺参数、吹净方式、烘干炉温度等方面进行系统研究,给出了一些解决方案.
A once overlooked source of electrolyte degradation incurred by dissolved manganese (Ⅱ) species in lithium-ion batteries has been identified recently.In order to deactivate the catalytic activity of such manganese (Ⅱ) ion,1-aza-12-crown-4-ether (A12C4) wi