【摘 要】
:
【诉说】母亲卧床5年,半年前,在我精心照料下安详离世。这5年,一言难尽!她躺在床上,形同植物人,护理的重担由我一人扛起来。远在深圳的妹妹常来电话,也常打钱。但说心里话,看
论文部分内容阅读
【诉说】母亲卧床5年,半年前,在我精心照料下安详离世。这5年,一言难尽!她躺在床上,形同植物人,护理的重担由我一人扛起来。远在深圳的妹妹常来电话,也常打钱。但说心里话,看着她在微信里晒这晒那的轻松样子,我真想说,我不要钱,我要你回来替替我,哪怕一周、一天、一小时呢。出殡时,妹妹回来了,跟母亲反目的弟弟也来了。他从小受宠,长大成人后心智不成熟,跟父母冲突不断。父亲被他气得突发心梗去世,母亲也被他作得心
[Complaint] mother five years in bed, six months ago, I meticulously under the care of death. This five years, a word difficult! She lay in bed, the same plant, the burden of care by me alone to carry it. Far from the sisters in Shenzhen often call, but also often hit money. But to be honest, watching her in the Wechat in the sun that relaxed look, I really want to say, I do not want money, I want you to come back to replace me, even a week, one day, one hour yet. When the funeral, my sister came back, and my mother was also against his mother came. He was favored childhood, immature mentally mature, with his parents continue to conflict. His father died suddenly of sudden myocardial infarction, his mother was also made for his heart
其他文献
As we know, the application of the ordinary oldham coupling is limited by its inertial force and low wear resistance.This paper deals with a method to balance
IntroductionPolyhydroxyalkanoates(PHAs)arebiopoly-merssynthesizedbymanybacteria.Afterthedetectionofpolyhydroxybutyrate(PHB),a...
Introduction Polyhydroxyalkanoates (PHAs) arebiopoly-merssynthesizedbymanybacteria. Afterthedetectionofpolyhydroxybutyrate (P
当零件尺寸超差时,一般以核算强度和加工相应的配合件来解决,这对关键尺寸和重要尺寸有时是不适用的,因不能互换。用尺寸链理论,成功解决了关键件尺寸的超差。
When the pa
啮出作用是降低啮轮噪音和磨损的一种技术. 在齿轮啮合过程中,齿在啮入时的摩擦系数大约是啮出时的两倍.由子啮出时磨损时小于啮入磨,若将啮入最小化、啮出最大化,传动效率
分析了变压器空载试验时铁心温升过程的温度数据,得出试验点温升曲线的数学模型,其表达式中热时间常数为时间的一次函数,而试验点的极限温升可直接求出。在整个温升过程中由
利用手性源(2R,3S)-3,4-二甲基-2-苯基-1,4-氧氮杂-5,7-二酮(1)合成了具有光学活性的7,8-二甲基-3,6-二苯基-5-氧-8-氮螺[2.6]壬-4,9-二酮(3).测定了化合物(3)的晶体结构,并讨论了在环加成反应
新车都需要磨合,因为新车各个零部件之间还没结合好,新车出厂,开始行驶的时期,由于车子各部分的运动部件还没有磨合,因此,必须谨慎使用,否则将会加剧零部件的损伤。而磨合期
用直流放电产生CF2自由基,在超声射流冷却下获得了CF2A1B1←X1A1250nm附近的激光诱导荧光激发谱。对不同带系的39个振动带做了归属,其中23个振动带是新标识的。澄清了前人对CF2A←X跃迁的一些不能肯定的归属
横截面是椭圆、圆、圆环构件的疲劳分析,直接牵涉到截面在载荷谱中各级循环载荷(简称循环)下的损伤度严重点。分析这类构件常用均匀取点法。其缺点是:(1)通常需要取很多点,
作者根据机械强度概率计算的一般原理,讨论了圆弧齿轮疲劳强度的可靠性计算方法,该方法是建立在常规设计基础上的,能预报齿轮的失效概率,也能为修改常规设计结果提供依据。并