Shrinkage porosity exists more or less in heavy castings, and it plays an important role in the fatigue behavior of cast......

请下载后查看，本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view......

During heat treatment process, the distortion behavior inevitably appears in hydraulic turbine blade castings. In this r......

The photographs are sought on the following:1.The forefront scenes for scientific research and production of foundry ind......

By means of induction melting technology,Ti-6Al-4V alloy staging casting was made with the same rotation velocity and ce......

It was analyzed that the finite element-cellular automaton (CAFE) method was used to simulate 3D-microstructures in soli......

The key manufacturing technologies associated with composition, microstructure, mechanical properties, casting quality a......

Centrifugal casting was applied to produce cylindrical castings using SiCp/Al composite slurry,which contained 20%SiC pa......

In the reign of Emperor Qianlong,Qing Dynasty(1736 AD-1795 AD)Each lion has a height of approximately 2.4 m,a length of ......

The effects of metallurgical and processing parameters on the formation of shrinkage cavities and p......

In order to know the behavior of non-metallic inclusions in centrifugal induction electroslag castings (CIESC), non-met......

Facing the market economy and global challenge the development of manufacturing industry especially casting industry is ......

The three dimensional solidification simulation of the single crystal investment castings at withdrawal rates of 2 mm祄i......

The hot compressive deformation of extruded AZ31magnesium alloy with the mass fractions of Al and Zn equal to 3 % and 1 ......

The mold filling and solidification simulation for the high pressure die casting (HPDC) and low pressure die casting (LP......

In order to produce the fully equiaxed and fine grained pure Al, a simple casting process that used cooling slope was e......

The variation of casting hot spot with proceeding of solidification and components of casting-mold system is studied by......

By making castings that pick up gas from moisture in red sand molds,the porosity generated at different cooling rates wa......

As an official transaction of Foundry Institution of Chinese Mechanical Engineering Society (FICMES), FOUNDRY Journal (m......

This article presents a new method to obtain local reinforcement in near-surface layers of channels in castings made of ......

This paper expatiates on domestic status of heavy steel casting production, with a special focus on hydraulicturbine cas......

According to the document requirements of the credit work office under the Ministry of Commerce of the People’s Republi......

Causes for central shrink pipe of GCr15 blooms were analyzed.Countermeasures to tackle with such defect were practiced,i......

Lost-foam casting is a 21st century green casting technology. Over the past decade, there has been an extraordinary deve......

The remarkable heredity of liquid aluminum modified by electric pulse (EP, EPM) has been uncovered. For better understan......

In this research, the materials and the compositions of the surface slurries were chosen by considering the characterist......

A motorcycle component of damper housing was made by semi-solid forming process. This was used to investigate the effec......

In order to improve the mould filling ability, the method for production of thin-walled castings in the travelingmagnet......

Due to the competition and high cost associated with die casting defects, it is urgent to adopt a rapid and effective m......

The three-dimensional solidification simulation of the investment castings of single crystal hollow turbine blade at th......

Fe-C-Si-Mn alloy castings used as blades in hydroelectric generators are studied and found to contain network structures......

RMB 10t坛沁段md Yu.n/unit布┏━━━━━━━━━━━━━━━━━━━━━━━━━━━━┳━━━━━━┳━━━━━━━━━......

1 .IntrOdUction High一strength,light一weight and large一size alumimimalloy eastings are widely used in aviation,astronav......

Hot crack is one of common defects in castings, which often results in failure of castings. This work studies the forma......

1 .Introduction The shell process is unique in its ability to make excellentreproducible castings with better surf......

The interior of a high-pressure die-casting is of an unsatisfactory quality. Engine blocks made with this die casting pr......

Computer simulation codes were developed based on a proposed mathematical model for centrifugal mold filling processes ......

Tsinghua-TOYO Research and Development Center of Magnesium and Aluminum Alloys Processing Technology was officially esta......

1 .IntroCtion Seleetive Laser Sintering(SLS)15 an imPortant field ofRaPid PrototyPing(RP),due to its caPability ofProees......

The mathematics model for temperature field of water-cooling copper crucible induction skull melting process was establi......

Based on the numerical simulation of solidification of castings, a thermal stress formula and a thermal crack initiation......

A mathematical model to calculate the size and distribution of microporosities was studied and coupled with a stochasti......

When heavy machines and large scaled receiver system of communication equipment are manufactured, it always needs to pr......

History of art casting in china has been over 5000 years. In the past few thousand years, numerous forming and decorati......

The high efficiency mechanized foundry technology of castings produced by using water-cooled copper alloy permanent mold......

Mold-filling process of thin-walled castings under the condition of traveling magnetic field has been studied by physic......

The mechanical properties and internal quality of low carbon martensite Electroslag Remelting Casting (ESRC)stainless st......

The squeeze cast technology is only applicable, at present, to the castings with a ratio of height to thickness less tha......

with the development of computer technology, foundry CAE technology has made rapid progress. Commercialsoftware packages......

In addition to mold rigidity and metallurgical quality of iron melting, the main reasons causing riser feeding failure i......