• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Modeling of ferrite-austenite phase transformation in low-carbon steels

Modeling of ferrite-austenite phase transformation in low-carbon steels

来源 :1st International Conference on Computational Design and Sim | 被引量 : 0次 | 上传用户：thomas012
【摘 要】
：
　　A two-dimensional cellular automaton (CA) model is adopted to simulate the ferrite (α)-austenite (γ) transformation in low-carbon steels.The nucleation of
【作 者】
：
DongAn[1]ShiyanPan[2]TingDai[1]BruceKrakauer[3]MingfangZhu[1] 
【机 构】
：
Jiangsu Key Laboratory for Advanced Metallic Materials, School of Materials Science and Engineering,
【出 处】
：
1st International Conference on Computational Design and Sim
【发表日期】
：
2015年期
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
　　A two-dimensional cellular automaton (CA) model is adopted to simulate the ferrite (α)-austenite (γ) transformation in low-carbon steels.The nucleation of austenite, the driving force of phase transformation, carbon redistribution at α/γ interfaces, and carbon diffusion in both the α and γ phases are factored in the present model.
其他文献
Nonlinear dynamic analysis and fatigue life prediction of ice-wind loads on transmission line
会议
Numerical simulation of reverse transformation and partition of solute elements during intercritical
　　Recently, a new class of TRIP steels without Si or Al but containing 5-10 wt% Mn have been considered as potential third-generation automotive steels.This M
会议
Multiscale simulation of nanoindentation response of aluminum with different crystal orientations an
　　A multiscale simulation method, qausicontinuum(QC) method was applied to study the nanoindentation with a cylindrical indenter and a single crystal aluminum
会议
Mechanical characterization and acoustic properties of the metallic foam with open cell of Tin-Lead
　　Cellular materials are inherently lighter than dense homogeneous materials.These materials can make several remarkable properties combining applications suc
会议
Analyzing standing waves on periodic waveguides by pseudospectral modal method
　　For some periodic waveguides, there are standing waves, which are special guided modes, non-propagating and localized around the waveguide core.These non-pr
会议
Digital material analysis methods based on computer vision
　　Machine Vision is a method replaces eye measure and estimate, Image acquisitions device getting target image then switches it into digital signal.Send it to
会议
Discussion on the methods to calculate austenite static recrystallized faction
　　Double deformation technique is often used to study static recrystallization behavior of materials and static recrystallization fraction can be calculated b
会议
The study of stress-strain reconstruction method based on EMD
　　At present, an effective means of structural health monitoring is through the installation of monitoring instruments to monitor the state of the system, one
会议
Angle and the accuracy of springback steel bar bending hoop stirrup
　　The hooked steel will spring back under the effection of residual stress, in order to improve the precision of the hoop, springback angle should be taken in
会议
FEM simulation and evaluation for large marine crankshaft manufacturing process
　　Crankshaft is one of the most important components in the large vessels, which act as the heart of diesel engine.Manufacturing the crankshaft runs a long co
会议