Selective laser melting of aluminium composite reinforced with carbon nanotubes

来源 :15th International Conference on Aluminium Alloys(ICAA15)(第十 | 被引量 : 0次 | 上传用户：szcentsweb

【摘要】

：

【作者】

：

Xihe Liu Xin Zhou Florian Eibl Zhijian Shen Wei Liu Wilhelm Meiners Reinhart Poprawe

【机构】

：

Tsinghua University, China Fraunhofer Institute f

【出处】

：

15th International Conference on Aluminium Alloys(ICAA15)(第十

【发表日期】

：

2016年3期

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

Previous work has shown that utilising carbon nanotubes (CNTs) as reinforcement for aluminium composite is of vital importance and great advantage.Selective laser melting (SLM), as a unique additive manufacturing processing method, provides a high potential in CNTs homogeneously dispersion in the composite.

其他文献

Study on the microstructural evolution of a new type Al-Zn-Mg-Cu ahoy with Er and Zr additions durin

The presence of large constitutive particle formed during solidification decreases the strength and hot workability of aluminium alloys.Therefore, the evolution of these phases is a major issue in the

会议

The influence of heat treatment on phase composition, texture and mechanical properties of Al-Cu-Li

Phase composition, texture and mechanical properties of 80 mm plates from Al-2.8Cu-1.7Li-0.5Mg-0.5Zn-0.1Zr-0.06Sc alloy were investigated.It has been found that strength characteristics are maximum in

会议

The effect of the thermo-mechanical treatment of pre-aging, pre-stretching and re-ageing on microstr

A new thermo-mechanical treatment consisting of pre-aging, pre-stretching, and re-aging was used to improve mechanical properties of 7093 Al alloys casting by ourselves.Hardness testing, ensile testin

会议

An innovative methodology for optimisation of properties, costs and sustainability of aluminium allo

The present paper describes an innovative methodology for optimization of product properties, production costs and environmental impact in fabrication of aluminium alloys.The main idea is to represent

会议

Experimental and numerical investigations on back-end effects of hollow aluminium profile during por

Back-end effect is one of most common effects during hollow profile extrusion, which has great influence on the product rate and production costs.The purpose of the present study is to investigate exp

会议

A quantitative study on the influence of through thickness texture variation on the anisotropic mech

The anisotropic mechanical behavior of aluminum extrusions is of interest to industry in terms of formability and crash behaviour.Depending on the homogenization and extrusion conditions a wide range

会议

Persistence of shear-type textures during annealing of ECAE-processed ultrafine grained materials: A

Understanding the annealing behavior of ultrafine-grained materials produced by severe plastic deformation is of interest for applications requiring a balanced strength and ductility.In this study, co

会议

Numerical simulation of residual stress in Al-Cu alloy component during quenching and reduction of q

In this study, residual stress development during quenching and cold compressive stress relief processes of complex component were studied by numerical simulation and experimental methods.An iterative

会议

Tube hydroforming characteristic of Al alloy with different heat treatment conditions

Tube hydroforming is metal forming technology that utilized internal pressure and axial compressive loads to generate designed product shapes with complex section from tubular materials.The tube hydro

会议

Effect of Cu and Mg/Si ratio on the intergranular corrosion resistance of 6000-series aluminum alloy

6000-series aluminum alloys with high Cu or excess Si addition were susceptible to intergranular corrosion (IGC).The corrosion behavior of four alloys with different Cu content and Mg/Si was investiga

会议

Selective laser melting of aluminium composite reinforced with carbon nanotubes

与本文相关的学术论文