【摘 要】
:
This paper aims at the unconventional triple porosity reservoir with fracture and vugs, according to the basic percolation principle the non-linear testing flow model with the quadratic pressure gradi
【机 构】
:
Southwest Petroleum University Huabei Petroleum
【出 处】
:
2007年油气藏地质及开发工程国家重点实验室第四次国际学术会议
论文部分内容阅读
This paper aims at the unconventional triple porosity reservoir with fracture and vugs, according to the basic percolation principle the non-linear testing flow model with the quadratic pressure gradient term has been established, for the pseudo-steady and the unsteady interporosity flow of the matrix and vugs to fracture. For the pseudo-steady interporosity flow model, by use of Douglas-Jones prediction- correction numerical method, the partial differential flow equation has been solved. For the unsteady interporosity flow model, by use of the variable substitution, linearizing the governing equation, the model has been solved, then obtained the Laplace space analytic solution and procured the real space solution by use of the Stehfest numerical inversion. In the end, the pressure and the pressure derivative log-log type curves have been drawn up.From the physical percolation mechanism, this paper has also analyzed the influence of the dimensionless quadratic pressure gradient coefficient to the curve shape characteristics of triple porosity reservoir. The impact of the quadratic gradient under certain conditions is extremely intense, and the pressure error is up to 20% and pressure derivative error is up to 30%. Especially for low permeability reservoirs and heavy oil reservoirs, its quadratic gradient coefficient is bigger than the conventional reservoirs; therefore its type curves deviation is much obvious. So if the flow equation ignored the quadratic term will cause a great error of the well test analysis results, the obtained parameter value will not be the real formation parameter value, which will greatly affect the sequel development and dynamic analysis. Therefore, the quadratic pressure gradient term should not be neglected, and the thorough research to the quadratic gradient percolation theory and application should be conducted. The result available can be used in the study of the flow rule and the well test analysis of triple porosity Reservoir.
其他文献
Based on the mathematical models of coupled fluid flow and deformation in Fluid-saturated porous media proposed by the author, the governing equations for 2D flow in confined aquifer are obtained, the
钻井过程中,为了有效地实施堵漏作业,必须明确漏失井段的位置和漏失性质。川东北构造上部砂泥岩地层承压能力低,而嘉陵江组到飞仙关组海相地层存在异常高压、压力系数高达2.2,钻井液柱压力接近上覆地层压力,容易形成诱导缝并促使宏观和微观的天然裂缝纵横向延伸,井漏分布区间明显拓宽,钻井液密度高、窗口窄,造成井漏频繁严重。根据研究工区钻井液漏失现象在测井曲线上的显示特征,建立了通过常规测井资料结合成像测井资料
推动膨胀芯头运动的液压膨胀力大小是膨胀管系统的关键参数之一,膨胀芯头与套管内壁间的摩擦系数、套管的膨胀幅度和膨胀芯头的锥角等对其均有直接性的影响。由于膨胀管的膨胀过程属于高度非线性弹塑性接触问题,很难利用解析法进行精确研究。本文利用有限元法建立了膨胀管膨胀过程的平面非线性接触力学模型,分析得到了摩擦系数、膨胀率和膨胀芯头锥角和所需液压膨胀力的关系曲线和定量关系拟合计算公式,最后通过统计学中的多元线
In conventional drilling, the screw centralizer rotates with drilling string at a high speed. When drilling fluids passes through the screw centralizerin annulus, the drastic swirl generated by screw
Acoustic time is the reflection of mechanical strength of rock. The study on shale hydration based on acoustic time can reflect the metabolic feature of strength and stability of borehole wall and sha
已有的研究表明致密储层容易受到应力敏感损害,渗透率大幅降低且不可逆,必然对致密砂岩气体高效产出造成影响。本文选取四川盆地、鄂尔多斯盆地典型致密砂岩样品,通过高精度比表面分析仪测量岩样的微孔径、进行单面进汞测试以及常规四面进汞测试等研究致密砂岩微观孔隙结构。实验研究了在有效应力条件下,不同压差、不同含水饱和度以及有效应力作用时间等岩样中气体传质行为,结果表明,随着有效应力的增加,致密储层孔喉随之变小
随钻测井同常规电缆测井一样,仍受井眼、围岩、地层倾角和地层各向异性及泥浆侵入等环境因素影响,若要有效地利用随钻测井资料就需对其环境影响因素进行必要的校正。目前随钻测井环境影响校正主要采用经典图版法,这种手工查图版校正费时费力,急需将图版最优回归拟合成数学公式,编程实现其环境影响的自动校正。采用哪种数学方法和公式模型进行随钻测井解释图版的高精度拟合便是关键所在。由于随钻测井资料相对于常规电缆测井资料
The sonic propagation velocity in rock mass is a good kind of information to reflecting the synthetical physical property of rock. The explanation of acoustic log information will based on the experim
The problem of severe deviation control is already exposure in the gas drilling experimentation of inland oil and gas fields. To controlling deviation, the actual WOB is usually adopted in the lower r
The main objective of this paper is to establish a consistent geometrical frame focusing on the coupling between hydro-mechanical aspects of the sanding process and formation deformation/collapse. A s