【摘 要】
:
Aiming to achive the high RF performace AlGaN/GaN HEMT by suppress current collapse and decresing the parasitlic parameters,high density SiN film was deposited by using ICP-CVD on the surface of AlGaN
【机 构】
:
School of Electronic Science and Engineering,Southeast University,and Key Laboratory of Micro-Inerti
【出 处】
:
2015 Shanghai Thin Film Conference(2015上海薄膜国际会议)
论文部分内容阅读
Aiming to achive the high RF performace AlGaN/GaN HEMT by suppress current collapse and decresing the parasitlic parameters,high density SiN film was deposited by using ICP-CVD on the surface of AlGaN/GaN epi wafer before fabrication of device.The GaN HEMT device was fabricated by removing PECVD passivation around the gate based the etch stop layer of high density SiN.A 6fingers × 50μm GaN HEMT device was fabricated.The device shows a maximum drain current of 900 rnA/mm and a maximum transconductance of 380 mS/mm,a current gain of cut-off frequency(fT)of 45GHz at a gate bias of-1.5V and a drain bias of 20V.The device shows a power density of 4.7W/mm,a power-added efficiency(PAE)of 44.6%and a associated power gain of 8.5dB by Load-pull measurement.A 34-36GHz GaN MMIC was fabricated,which exhibbits a output Power saturation about 41.5dBm,a power-added efficiency(PAE)of 20%and a gain of 15.5dB.
其他文献
以氧化石墨烯、正硅酸四乙酯和苯胺单体为原料,采用两步法制备了石墨烯/二氧化硅/聚苯胺三元复合材料.采用循环伏安法对材料进行电化学性能测试[1],结果表明,当氧化石墨烯与苯胺单体的投料比为1:50时,在1 MH2SO4电解液中,在扫描速度1 mV/s下,三元复合材料的比容量达554.5 F/g,远大于石墨烯/二氧化硅的比容量(144 F/g).
The development of environment-friendly and high energy density cathode materials is highly desired for the clean and sustainable Li-ion batteries (LIBs) system.To take advantage the effect of oxygen-
The atomic layer deposition (ALD) technique is a surface-controlled and layer-by-layer process,relying on two sequential self terminating half-reactions,offering unmatched precision in terms of contro
Nowadays,although Li ion battery technology is sufficient to power small portable devices such as mobile phones and lap-top computers,significant challenges in the specific capacity and rate capabilit
锂离子电池使用的正极材料多为可逆脱/嵌锂离子的层状氧化物,传统正极材料如LiCoO2、LiNiO2等存在着各种不可避免的缺点,LiCoO2实际放电比容量较低、成本高、毒性大,LiNiO2热稳定性和结构稳定性较差[1].三元材料LiNixCoyMn1-x-yO2是三种层状氧化物不同比例混合的固溶体,具有比容量高、循环性能好、成本低、环境友好等优点,近年来受到广泛的关注和研究.
本文将溶胶-凝胶法与共沉淀法相结合,探索出了一种液相制备NCA材料新方法.SEM测试结果表明制备出的Ni0.85Co0.12Al0.03(OH)2前躯体为8-12μm球形颗粒,其表面为细丝状,经溶胶法锂化高温烧结得到NCA材料仍为球形颗粒,颗粒平均粒径为8-12μm,其表面则为多面体结构.充放电测试结果表明该材料在2.75-4.25V电压范围内,0.1C电流密度下,放电比容量高达196mAh/g.
Recently,2D materials,such as graphene,MoS2,TaSe2 and WS2,have received great research interests due to their unique electronic,optical,and chemical properties.Mica is a well-known layered silicate co
Copper has been proposed as a new material for metallization in Si-based semiconductor devices due to its low resistivity,high chemical stability,and excellent electromigration resistance.In this pape
Printed electronics is an emerging industry aimed at large-scale and ultralow-cost application of electronic products,and will play a very important role in the field of organic thin film transistors(
Organic flexible devices have attracted a surge of interest owing to their attractive properties and their applications in future paper displays,solar cells,and wearable electronics etc.Photodetectors