Spinal Cord Kinking in Thoracic Myelopathy Caused by Ossification of the Ligamentum Flavum

来源 :中华医学杂志(英文版) | 被引量 : 0次 | 上传用户:nvllnvll
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Background:Ossification of the ligamentum flavum (OLF) is being increasingly recognized as a cause of thoracic myelopathy.This study was to describe a rare clinical entity of spinal cord kinking (SK) in thoracic myelopathy secondary to OLF.Methods:The data of 95 patients with thoracic myelopathy secondary to OLF were analyzed retrospectively.The incidence and location of SK were determined using preoperative magnetic resonance imaging (MRI).The clinical presentation and radiological characteristics in patients with SK were analyzed.Posterior en bloc laminectomy with OLF was performed,and the surgical results were evaluated.Results:SK was found in seven patients (7.4%) based on preoperative MRI.The patients included one male and six females with an average age of 55.6 years (range,48-64 years).Five patients presented with radiculomyelopathy and two presented with typical thoracic myelopathy of spastic paraparesis.In all cases,the kinking was located just above the end of the spinal cord where the conus medullaris (CM) was compressed by the OLF.The degree of SK varied from mild to severe.The tip of the CM was located between the upper third of T1 1 to the lower third of L 1,above the lower edge of L 1.With an average follow-up of 30.4 months,the modified Japanese Orthopedic Association score significantly improved from 5.7 ± 1.8 preoperatively to 8.9 ± 1.4 postoperatively (t =12.05;P < 0.0001) with an improvement rate of 63.1 ± 12.3%.Conclusions:SK is a rare radiological phenomenon.It is typically located at the thoracolumbar junction,where the CM is compressed by the OLF.Our findings indicate that these patients may benefit from a posterior decompressive procedure.
其他文献
主要对公路工程现场设备材料进行了研究,从施工现场设备材料计划管理和施工成本控制两个方面进行分析,最后提出提升公路施工成本控制和现场设备材料计划管理的若干建议.
我一直相信“住宅”这种人类社会最具历史与社会意义的建筑类型是人类文明进步的动力来源,而住宅同时也是稳定城市风格与特色形成最重要的元素与力量,如北京的四合院,上海的
以高速公路设计标准化设计内容为研究对象,分别从设计标准化与设计创新的关系、设计中过程存在的问题、设计标准化思路多方面,论述设计标准化的主要内容,实践证明,通过标准化
目的 建立永生化的人肝细胞系,为生物人工肝、肝细胞移植、体外药物代谢等提供细胞模型.方法 应用胶原酶等四步灌流法分离获得原代人肝细胞,以含有SV40大T抗原(SV40LT)的重组反转录病毒对原代人肝细胞进行永生化,并对永生化人肝细胞进行生物学特性鉴定.结果原代人肝细胞经含有SV40 LT的重组反转录病毒感染3~4周后,获得2株永生化人肝细胞系,分别命名为HepLi2和HepLi3,永生化人肝细胞在
石油化工机械、通用机械中的大直径法兰制造时,都是先切割钢板成环段——扇形块,然后将扇形块焊接成环形法兰。在切割之前,常用作图法做出纸片样板,再在钢板上画线。这种方
结合了具体的施工经验和相关资料,通过对软土路基的施工技术及处理措施进行分析,总结出了一些处理软土路基的要点.旨在从技术的角度解决公路工程施工中软土路基的问题,保障工
在化工原料甲醛的生产中,阻火器是重要的设备,它置于蒸发器和氧化器之间.图1所示的波纹板是阻火器的关键零件,材料为紫铜,在阻火器中绕轴盘旋在一起,同水蒸汽一道阻止火星窜
聚酯长丝土工布的制作工艺十分环保,主要过程就是将聚酯轻纺丝固结成无纺布,再通过针刺方式在无纺布上刺出渗透孔,这种由聚酯材料制成的聚酯长丝土工布是一种应用十分广泛的
RQC5Y-350热能去毛刺机,其工作原理是借助氢、氧气体的热化反应,产生3000~3500℃瞬时高温烧熔零件加工后残留的毛刺。爆炸缸的直径为240mm,长为200mm;最大充气压力2.5MPa,最
我厂生产的金刚石油压机液压管路压力高达150MPa,采用的管接头其结构如图1所示。 接头座采用45号钢调质处理硬度为269~302HB,密封面进行精车加工。油管接头采用40Cr钢淬火处