【摘 要】
：
The preparation of aluminum nitrogen (AlN) film without Al texture is of great significance for the manufacture of highperformance surface acoustic wave (SAW) device. We research the process factors which bring Al into AlN film due to radio frequency (RF)
【机 构】
：
TianjinKeyLaboratoryofFilmElectronicandCommunicationDevice,SchoolofElectronicsInformationEngineering
【出 处】
：
OptoelectronicsLetters
论文部分内容阅读
The preparation of aluminum nitrogen (AlN) film without Al texture is of great significance for the manufacture of highperformance surface acoustic wave (SAW) device. We research the process factors which bring Al into AlN film due to radio frequency (RF) magnetron sputtering system, and discuss how the process parameters influence the AlN thin film containing Al. In the research, it is found that the high sputtering power, the low deposition pressures and low partial pressure of Ar can lead to growing Al-texture during AlN thin film preparation, and the experiment also shows that filling the chamber with nitrogen gas can recrystallize a small amount of Al composition into AlN film during the annealing process in the high temperature environment.
其他文献
将双光互注入半导体激光器作为混沌光发射源,构建了受环境影响较小、稳定性较好的全光纤型混沌同步通信系统,并从延时特征的隐藏、接收与发射激光器的互相关性及输出混沌光带宽三方面研究该系统的同步通信能力。使用自相关函数及互信息函数等数学工具仿真计算该系统外腔反馈延时特征峰值、发射与接收激光器的互信息函数峰值及系统输出混沌光带宽。研究表明,通过适当调整参数使发射与接收激光器高度同步,双光互注入系统外腔反馈延时特征峰值可减小至0.1899,比相同条件下单光互注入的延时特征峰值降低了0.1696,接收和发射激光器最大互
This article summarizes work at the Laser Thermal Laboratory and discusses related studies on the laser synthesis and functionalization of semiconductor nanostructures and two-dimensional (2D) semiconductor materials. Research has been carried out on the
We present a novel high-energy, single-mode, all-fiber-based master-oscillator-power-amplifier (MOPA) laser system operating in the C-band with 3.3-ns pulses and a very widely tunable repetition rate, ranging from 30 kHz to 50 MHz. The laser with a maximu
基于神光Ⅱ升级装置,研究了纳秒/皮秒双束激光联合驱动双层靶的伽马(γ)辐射特征。利用ns束激光与CH薄膜靶相互作用,产生大尺度近临界密度等离子体,然后将ps束激光作用在该等离子体上,产生高能电子,高能电子穿过2 mm厚的Au靶,通过轫致辐射产生γ射线。对不同方向的γ辐射能谱和靶室外的γ辐射剂量分布进行实验测量,发现γ辐射集中在激光前冲方向,具有较小的发散角,而且在该方向上高能段的γ辐射较强。这说明双层靶的设计可以提高ps束激光与等离子体的能量耦合效率,提高高能电子温度,增加高能电子数目,有利于高能段γ辐射
We propose a design of single-mode orbital angular momentum (OAM) beam laser with high direct-modulation bandwidth. It is a microcylinder/microring cavity interacted with two types of second-order gratings: the complex top grating containing the real part
Photodynamic therapy (PDT) has been a routine treatment of tumors and some microvascular diseases, but clinically available photosensitizers are still scarce. Among all kinds of photosensitizers, hypocrellins possess the most characteristics of ideal phot
提出一种基于马尔科夫链蒙特卡罗(MCMC)框架的子图学习方法,该方法通过构建马尔科夫链实现子图在状态空间中的迭代,最终得到用于匹配的最优子图,以有效提高图匹配的精度,减少离散值的影响。在此过程中,所提方法可以在一对一的匹配约束下有效保存成对的匹配点,同时避免了离散值和畸变值的影响。实验分别在合成图像数据集、真实图像数据集、3D模型数据集上展开,实验结果证明了所提方法在图匹配过程中的优越性。
误码率(BER)是非对称限幅光正交频分复用(ACO-OFDM)的一项重要性能指标，子载波个数是影响这一性能指标的重要因素。通过理论推导及仿真证明的方法，分析了子载波个数对光域单边带ACO-OFDM信号在单模光纤中传输时系统误码率的影响。结果表明，在总传输速率一定时，改变子载波个数从128个到16384个，所需要的总带宽改变不超过0.775%。并在此基础上，通过实验证明了不同的传输速率下ACO-OFDM系统均存在使系统误码率最低的最优子载波个数，实验结果表明该最优子载波个数随传输速率的增加而增加。
在大型结构件的损伤监测过程中,摄像机镜头畸变往往引起成像畸变,如果直接利用畸变图像进行标定、测量,将引起较大误差,降低损伤监测精度。为了有效地校正成像畸变,提出一种改进的基于直线特征的非量测畸变校正方法。分析实际测量中成像畸变的像差模型;直接利用场景中存在的直线特征,得到带权重因子的直线射影不变约束关系和三点近似共线约束关系,并建立两组畸变校正约束方程求解畸变系数;通过实验验证提出方法的可行性和有